Gemini PS-676i Manuel d'utilisateur télécharger pdf (Page 5)

(5)

HINT: BOOTH OUTPUT (6) IS USED BY SOME DJS TO RUN MONITOR SPEAKERS IN THE DJ

BOOTH. YOU CAN ALSO USE IT AS A SECOND ZONE OR AMP OUTPUT.

NOTE: THE RECORD OUT (7) HAS NO LEVEL CONTROL. THE LEVEL IS SET BY THE CHANNEL

SLIDES AND THE GAIN CONTROLS OF THE SELECTED CHANNEL. TONAL QUALITIES ARE

SET BY THE LOW, MID AND HIGH CONTROLS OF THAT SAME CHANNEL.

7. TALKOVER SECTION: The purpose of the TALKOVER SECTION is to

allow the program playing to be muted so that the MIC (13) can be

heard above the music. When the TALKOVER (34) button is pushed, the

TALKOVER INDICATOR (35) will glow and the volume of all sources

except the MIC (13) or whatever is connected to the PHONO 1/LINE 1

(12) input are reduced by 16 dB.

8. CUE SECTION: By connecting a set of headphones to the HEADPHONE

(16) jack, you can monitor any or all of the channels. Select the correct

CUE (36) button or buttons and their respective CUE LED (37) indicators

will glow. Use the CUE LEVEL (38) control to adjust the headphone

volume without effecting the overall mix. By sliding the CUE PGM PAN

(39) control to the left you will be able to monitor the assigned cue

signal. Sliding to the right will monitor the PGM (program) output.

9. DISPLAY: The peak hold, dual function DISPLAY (40) indicates either

the MASTER (5) output left and right levels or the CHANNEL 2 and

CHANNEL 3 levels. You can choose the option you want by pressing

the DISPLAY (41) button.

NOTE: WHEN THE DISPLAY (40) IS IN THE CHANNEL 2/CHANNEL 3 DISPLAY MODE, BY

ADJUSTING THE INDIVIDUAL CHANNEL GAIN AND TONE CONTROLS, YOU CAN

INCREASE OR DECREASE THE SIGNAL TO MATCH THE OTHER CHANNEL’S SIGNAL. THE

CHANNEL SLIDES AND CROSSFADER HAVE NO EFFECT ON THE DISPLAY READINGS.

10. The CROSSFADER CURVE SWITCH (42) allows you to adjust the kind

of curve the crossfader has. Move switch to the “sharp” position to

make the curve steep and cutting (perfect for scratching ). Move switch

to the “gradual” position to make the curve gradual and gentle. The

CROSSFADER REVERSE SWITCH (43) allows you to reverse the

crossfader so that CHANNEL 3 is controlled by the left side of the

crossfader and CHANNEL 2 is controlled by the right side of the

crossfader.

NOTE: WHEN THE CROSSFADER REVERSE SWITCH (43) IS ACTIVATED, ONLY THE CROSSFADER

REVERSES. THE CHANNEL SLIDES, GAIN, AND TONAL CONTROLS DO NOT REVERSE.

PS-676i ONLY:

SAMPLER OPERATION:

The PS-676i Sampler uses Dynamic RAM Memory and a 12 bit

microprocessor controller. The full bandwidth results in true sound

reproduction.

SAMPLE RECORD:

1. Put the MODE SELECTOR (44) switch into the WRITE position.

2. Select the source you want to sample from by pressing the appropriate

ASSIGN BUTTON (45).

3. The PS-676i is equipped with a SAMPLER REC/PLAY LEVEL (46)

control.When the MODE SELECTOR (44) is in the WRITE mode, this

control acts as a record level control. If the OVERLOAD INDICATOR (47)

is blinking, it means that the input signal you are going to sample is

too strong and will cause the sample to be distorted. Lower the sample

signal intensity by turning the SAMPLER REC/PLAY LEVEL (46) control

counterclockwise.

4. If the OVERLOAD INDICATOR (47) is off, turn the SAMPLER REC/

PLAY LEVEL (46) control clockwise until the OVERLOAD INDICATOR

(47) begins to blink and then turn the SAMPLER REC/PLAY LEVEL (46)

counter clockwise until the OVERLOAD INDICATOR (47) just goes off.

5. Tapping the START/STOP (48) button begins the sampling process (the

SAMPLER INDICATOR (49) will illuminate RED). Tapping the START/

STOP (48) button a second time ends the sample (the SAMPLER

INDICATOR (49) will turn off). If you do not tap the START/STOP (48)

button a second time, the sampling process will stop automatically after

12 seconds.

SAMPLE PLAYBACK:

1. Put the MODE SELECTOR (44) switch into the SINGLE or REPEAT

position.

2. When the MODE SELECTOR (44) is in the SINGLE or REPEAT mode, the

SAMPLER REC/PLAY LEVEL (46) control acts as a Sampler Level

Control.

3. Tapping the START/STOP (48) button with the MODE SELECTOR (44) in

the SINGLE position will cause the sampler to playback one time (the

SAMPLER INDICATOR (49) will illuminate GREEN). Every push of the

START/STOP (48) button will restart the sample from the beginning.

Rapid pressing of the START/STOP (48) button will cause a stuttering

effect. Once the sample has started playback and the START/STOP

(48) button is not pushed a second time, the sample will play to the end

and then stop (the SAMPLER INDICATOR (49) will illuminate turn off).

4. Tapping the START/STOP (48) button with the MODE SELECTOR (44) in

the REPEAT position will cause the sample to continuously play over and

over (the SAMPLER INDICATOR (49) will illuminate GREEN). The

START/STOP (48) button will act as an on/off switch. The first push will

start the sample, the second push will stop it.

ROBO PLAY:

1. With the ROBO PLAY (50) button in the OFF position (the ROBO PLAY

INDICATOR (51) will be OFF) and the MODE SELECTOR (44) switch in

either the SINGLE or REPEAT mode, pressing the START/STOP (48) will

cause the sample to play along with the signal going through the mixer.

2. When the ROBO PLAY (50) button is in the ON position (the ROBO PLAY

INDICATOR (51) illuminates RED), starting the sampler mutes the signal

going through the mixer. When the sample ends, the signal automatically

turns back on.

PITCH CONTROL:

The PS-676i comes equipped with a sampler PITCH (52) control. To

adjust the tone of a sample, turn the knob to the left to slow the pitch

and to the right to speed up the pitch after a sample has been recorded.

The pitch can also be set while recording a sample.

HINT: YOU CAN RECORD A SAMPLE WITH THE PITCH (52) CONTROL IN ANY POSITION.

WHATEVER THAT POSITION IS WILL BECOME THE “NORMAL” SOUND. IF YOU START TO

RECORD A SAMPLE WITH THE PITCH (52) CONTROL SET AT MINIMUM (THIS NOW

BECOMES YOUR NORMAL PITCH), BY INCREASING THE PITCH TO MAXIMUM, THE PITCH

EFFECT WILL DOUBLE IN SPEED. RECORDING AT MAXIMUM AND LOWERING TO

MINIMUM WILL DO EXACTLY THE OPPOSITE.

PAN CONTROL:

SAMPLER PAN (53): This lets you hear the sample in either stereo

mode or by turning SAMPLER PAN (53) to the left or right will change

the range from the left channel to the right channel of sound, for the

sample.

SPECIFICATIONS

INPUTS:

DJ Mic...........................................................................1.5mV 2 k unbalanced

Phono @ 1 kHz.............................................................................2 mV 47 kW

Line...........................................................................................100 mV 27 kW

OUTPUTS:

Amp/Booth........................................................................0 dB 775mV 400 W

Max......................................................................................24V Peak-to-Peak

Rec..............................................................................................225mV 5 kW

GENERAL:

Bass ........................................................................................+ 12dB/- 32 dB

Mid ...........................................................................................+ 12dB/- 32 dB

Treble ......................................................................................+ 12dB/- 32 dB

Gain (Mic)........................................................................................0 to -40dB

Gain (Chnls 1-3)..............................................................................0 to -20dB

Frequency Response....................................................20Hz - 20kHz +/- 2dB

Distortion................................................................................less than 0.02%

S/N Ratio................................................................................better than 80dB

Talkover Attenuation................................................................................16dB

Power Source..........................................................115/230V 50/60Hz 20W

Dimensions.....................................................254mmW x 305mmD x 112mmH

10”W x 12”D x 4 7/16”H

Weight.........................................................................................6.5 lbs(3 Kg)

SAMPLER:

Sampler System.......................................................................12 Bit Sampling

Sample Length .............................................................................12 Seconds

Total Memory Capacity ...........................................................................1 Mbit

1 2 3 4 5 6 7 8 9 10 11 12

Commentaires sur ces manuels

Pas de commentaire

Gemini PS-676i Manuel d'utilisateur Page 5

Commentaires sur ces manuels

Produits connexes et manuels pour Instruments de musique Gemini PS-676i